Fanimation FP8094BN - Manual de uso

Fanimation FP8094BN

Ventilador de techo Fanimation FP8094BN - Manual de uso, léela gratuitamente en línea en formato PDF. Esperamos que esto te ayude a resolver cualquier duda que puedas tener. Si tienes más preguntas, contáctanos a través del formulario de contacto.

1 Page 1 2 Page 2 3 Page 3 4 Page 4 5 Page 5 6 Page 6 7 Page 7 8 Page 8 9 Page 9 10 Page 10 11 Page 11 12 Page 12 13 Page 13 14 Page 14 15 Page 15 16 Page 16 17 Page 17 18 Page 18 19 Page 19 20 Page 20 21 Page 21 22 Page 22 23 Page 23 24 Page 24 25 Page 25 26 Page 26 27 Page 27
Página: / 27
Página siguiente
Cargando la instrucción

How to Operate Your Ceiling Fan

16

Figure 1

Figure 2

Figure 4

Figure 5

MAIN FUSE BOX

For illustrative purposes only

-not

intended to cover all types of controls

2.

Restore electrical power to the outlet box by turning

the electricity on at the main fuse box. (Figure 2)

Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
c o n n e c t o r s , e x c e p t f o r t h e g r o u n d w i r e . D o n o t
operate fan until the blades are in place. Noise and
fan damage could result.

WARNING

1.

IMPORTANT:

Using a full range dimmer switch

(not included) to control fan speed will damage the fan.
To reduce the risk of fire or electrical shock, do not use
a full range dimmer switch to control the fan speed.
(Figure 1)

WARNING

Do not operate this fan with a variable (Rheostat) wall
controller or dimmer switch. Doing so could result in
damage to the ceiling fan's remote control unit.

3.

To make fan operational, install 23A/12V battery

(included) in hand-held remote transmitter, with fan
power off. Then follow the remote code setting
process. (If not used for long periods of time, remove
battery toprevent damage to transmitter). Store the
remote away from excessive heat or humidly.
(Figure 3)

NOTE: The remote unit has 32 different code
combinations. To prevent possible interference from or
to other remote units, simply change the combination
code in the remote and receiver.

4.

To set the remote code with a small screwdriver or

ball point pen (neither included), slide dip switches
firmly up or down. (Figure 4)

NOTE: Factory setting is all up. Do not use this

position.

Dip Switch

ON DIP

1 2 3 4 5

Remote

12V 23A

Battery (1 pcs)

Figure 3

5.

Remote functions: (Figure 5)

‡,QGLFDWRU/('OLJKWIDQVSHHG
‡EXWWRQ7XUQVIDQRII
‡)DQ6SHHG

Turns fan on and turns speed up.
Turns fan on and turns speed down.

‡/LJKWEXWWRQ7XUQVOLJKWRQDQGRII

Increases light output level.

Decreases light output level.

Tap and the fan and light will turn off after
3 hours.

Tap and the fan and light will turn off after
6 hours.

Tap and the fan and light will turn off after
1 hour.

Página siguiente

"Cargando la instrucción" significa que debes esperar hasta que el archivo se cargue y puedas leerlo en línea. Algunas instrucciones son muy grandes y el tiempo de carga depende de la velocidad de tu conexión a Internet.

Otros modelos de ventiladores de techo Fanimation

Todos los ventiladores de techo Fanimation