Hertz HMS 12 B2-LD-C - Manual de uso - Página 20
Subwoofer Hertz HMS 12 B2-LD-C - Manual de uso, léela gratuitamente en línea en formato PDF. Esperamos que esto te ayude a resolver cualquier duda que puedas tener. Si tienes más preguntas, contáctanos a través del formulario de contacto.
23
Owner’s Manual
FUSE
FUSE
FUSE
FUSE
RED
RED
RED
GREEN
GREEN
GREEN
BLUE
BLUE
BLUE
YELLOW
(+ 12 V)
YELLOW
(+ 12 V)
YELLOW
(+ 12 V)
+ 12 Vdc
Switched +12V
GND
2 Speakers
HMS 12
series
HMX 6.5 / HMX 8 / HMS 10
series
1 Speaker
N Speakers
COLOR
RED GREEN BLUE
WHITE
X
X
X
RED
X
GREEN
X
BLUE
X
YELLOW
X
X
PURPLE
X
X
CYAN
X
X
SERIES
FUSE VALUE
HMX 6.5
HMX 8
100 mA
HMS 10
250 mA
HMS 12
250 mA
COLLEGAMENTO DEL CIRCUITO LED
-
La tensione fornita al LED
non deve superare i 12,5 Vdc
riferiti a massa
(GND)
.
-
La tensione fornita al LED dovrebbe essere controllata da un
circuito di attivazione (+12V Switched)
per accendere il LED solo
quando necessario e spegnerlo quando l’imbarcazione non viene utilizzata o rimessa.
-
Proteggere con un fusibile da 100mA il cavo
YELLOW (+12V)
, poi connettere insieme i cavi
YELLOW (+12V)
di tutti gli speaker
al circuito
di attivazione (+12V Switched)
.
-
Proteggere con un fusibile la tensione fornita dal
circuito di attivazione (+12V Switched)
, il valore del fusibile deve essere calcolato
con la formula 100mA o 250 mA x N Speaker con il risultato approssimato al valore di fusibile standard più vicino. Esempio 6 speaker
(3 coppie) in parallelo richiedono 100mA x 6 = 600mA per il quale il valore standard più vicino è 630mA.
-
Collegare i cavi
R(Red), G(Green), B(Blue)
dallo speaker al sistema di massa
(GND)
seguendo la tabella sotto in funzione del colore
desiderato tra i 7 disponibili.
HMX 6.5-LD
/
HMX 6.5-LD-C
/
HMX 6.5-LD-TC
/
HMX 6.5-LD-TW
/
HMX 6.5 S-LD
/
HMX 8-LD
/
HMX 8-LD-C
/
HMX 8-LD-TC
/
HMX 8-LD-TW
/
HMX 8 S-LD
/
HMS 10 S-LD-G
/
HMS 10 S2-LD-G
/
HMS 12 B2-LD-W
/
HMS 12 B4-LD-W
/
HMS 12 B2-LD-C
/
HMS 12 B4-LD-C
/
HMS 12 S4-LD-G
/
HMS 12 S2-LD-G
LED direct wiring
*
Fuse value
per N Speaker
*
Fuse value
per N Speaker
OR
*
Fuse value
per N Speaker
*
Fuse value
per N Speaker
LED CIRCUIT WIRING
-
Voltage provided to the LED circuit must
not exceed +12,5 Vdc
referred to the system ground
(GND)
.
-
Voltage provided to the LED circuit should be switched by an
activation circuit
in order to turn-on the LED lighting only when
required and turn it off when vessel is not used or put into storage.
-
Protect the
YELLOW (+12V)
wire with a 100mA fuse, then connect the
YELLOW (+12V)
wires from all the speakers together to the
main
Switched +12 Vdc
.
-
Fuse the
Switched +12 Vdc
according to the total number of speakers connected in parallel. We suggest for the fuse value to be as close
as possible to the standard value corresponding to 100mA or 250 mA x N speakers rounded in excess. I.e. 6 speakers (3 pairs) in parallel
requires 100mA x 6 = 600mA, for which the closest standard fuse value rounded in excess would be 630mA.
-
Connect the
R(Red), G(Green), B(Blue)
wires from the speaker to the system ground
(GND)
referring to the below table according
to the color desired among the 7 available options.
"Cargando la instrucción" significa que debes esperar hasta que el archivo se cargue y puedas leerlo en línea. Algunas instrucciones son muy grandes y el tiempo de carga depende de la velocidad de tu conexión a Internet.
Otros modelos de subwoofers Hertz
-
Hertz HMS 10 S2-LD-G
-
Hertz HMS 10 S2-LD-SW
-
Hertz HMS 10 S4-LD-G
-
Hertz HMS 10 S4-LD-SW
-
Hertz HMS 10 S-LD-G
-
Hertz HMS 12 B2-LD-W
-
Hertz HMS 12 B4-LD-C
-
Hertz HMS 12 B4-LD-W
-
Hertz HMS 12 S2-LD-G
-
Hertz HMS 12 S2-LD-SW