Hotpoint HHM7SMWW - Manual de uso - Página 2

Hotpoint HHM7SMWW

Congelador Hotpoint HHM7SMWW - Manual de uso, léela gratuitamente en línea en formato PDF. Esperamos que esto te ayude a resolver cualquier duda que puedas tener. Si tienes más preguntas, contáctanos a través del formulario de contacto.

1 Page 1 2 Page 2 3 Page 3 4 Page 4 5 Page 5 6 Page 6 7 Page 7 8 Page 8 9 Page 9 10 Page 10 11 Page 11 12 Page 12 13 Page 13 14 Page 14 15 Page 15 16 Page 16 17 Page 17 18 Page 18 19 Page 19 20 Page 20 21 Page 21 22 Page 22 23 Page 23
Página: / 23
Página anteriorPágina siguiente
Cargando la instrucción

49-60816-1

INST

ALLA

TION

Preparing of Installation

Read these instructions completely and carefully.

Freezer Location

<RXUIUHH]HUVKRXOGEHFRQYHQLHQWO\ORFDWHGIRU

day-to-day use in a dry, well-ventilated room.

'RQRWLQVWDOOWKHIUHH]HUZKHUHWKHWHPSHUDWXUHZLOOJR
EHORZƒ)ƒ&RUDERYHƒ)ƒ&EHFDXVHLWZLOO

not maintain proper temperatures.

'RQRWLQVWDOOWKHIUHH]HULQDORFDWLRQH[SRVHGWRUDLQ

water or direct sunlight.

Be sure to install your freezer on a floor strong enough
to support it when it is fully loaded.

Level Freezer

Level the freezer from side to side and front to back

VRWKDWWKHOLGZLOOVHDOSURSHUO\8VHVKLPVWROHYHOWKH

freezer if necessary.

NOTE:

It should not be necessary to remove the lid

during installation. If, for some reason, the hinges need
adjustment, see instructions below.

Clearances and Ventilation

$OORZDWOHDVW´PPFOHDUDQFHRQERWKVLGHVRI
WKHIUHH]HUDQG´PPEHWZHHQWKHEDFNRIWKH

freezer and the wall. Leave room above the freezer to
open the lid.

.HHSIODPPDEOHPDWHULDOVDQGYDSRUVVXFKDVJDVROLQH

away from freezer.

'RQRWFRYHUWKHIUHH]HUZLWKLWHPVVXFKDVEODQNHWV

sheets, tablecloths, etc. This reduces air circulation.

Lid Removal

CAUTION

LIFTING HAZARD

7KHOLGLVKHDY\8VHERWKKDQGVWRVHFXUHWKHOLGEHIRUH

lifting.

CAUTION

HINGE SPRING UNDER TENSION

If it is necessary to remove the lid, follow these steps:

1. Remove each upper hinge cover by grasping on the

sides and pulling upwards. Remove each lower hinge
cover by grasping on the sides and pulling down.

2. Open the lid to the maximum position. (The hinges are

loosest at this position.)

3. Loosen, do not remove, the 4 screws from the lower

part of the hinge that are mounted to the cabinet.

4. Raise/lift the lid until the screws align with the larger

slotted openings in the bottom of the hinge. Each
hinge is still attached to the lid with 4 screws.

5. To reinstall lid follow steps in reverse. Tighten all

hinge screws but avoid over-tightening to prevent
stripping. Reinstall hinge covers.

8SSHU+LQJH

Cover

Lower Hinge
Cover

Hinge screws to
be loosened

Hinge screws
to be loosened

Página anteriorPágina siguiente

"Cargando la instrucción" significa que debes esperar hasta que el archivo se cargue y puedas leerlo en línea. Algunas instrucciones son muy grandes y el tiempo de carga depende de la velocidad de tu conexión a Internet.

Otros modelos de congeladores Hotpoint