Lasko 101 - Manual de uso - Página 2

®

Rev. B 4/11

2

100ES

Rev. B 4/11

7

100ES

SERIE 100

CONSEJOS PARA IDENTIFICAR PROBLEMAS

Si su calefactor se apaga inesperadamente o no funciona, es

probable que la función de seguridad descrita anteriormente

se haya activado para impedir el sobrecalentamiento.

1. Cerciórese de que el cable eléctrico esté enchufado en un

tomacorriente en buen estado.

2. Si su Calefactor opera durante varios minutos y se apaga

repetidamente, es posible que el mismo requiera limpieza.

Ver la sección de Mantenimiento abajo.

Si tiene algún problema que no pueda resolverse con los

pasos indicados más arriba, contacte a Asistencia Técnica al

1-800-233-0268, de lunes a viernes, entre las 8am y las 5pm

(Horario Estándar del Este de los Estados Unidos).

FUNCIONAMIENTO

(Figura 1)

1. Retire cuidadosamente el Calefactor de su bolsa y caja.

ADVERTENCIA:

Las etiquetas de plástico o caucho, quieren

los pies en esta unidad, pueden atascar a superficies de

muebles. La unidad puede salir un residuo que podría

oscurecer, poder manchar o podría salir imperfecciones

permanentes en el fin de ciertas superficies de muebles,

inclusive superficies de madera.

2. Coloque el Calefactor sobre una superficie firme y

plana.

3. Cerciórese de que la

Perilla de Encendido

del Calefactor

esté en la posición de

APAGADO

antes de enchufarlo a

un tomacorriente.

4. Conecte el cable a un tomacorriente de 120 voltios.

A s e g ú r e s e q u e e l e n c h u f e e n c a j e fi r m e m e n t e

e n e l t o m a c o r r i e n t e .

Cuando los enchufes quedan flojos dentro de

los tomacorrientes, podrían deslizarse parcial

o completamente fuera del tomacorriente

con el menor movimiento del cable adosado.

Los tomacorrientes en este estado podrían

sobrecalentarse y representar un peligro de

incendio grave; si queda cubierto por una cortina

o tela, el peligro de incendio es todavía mayor.

5. Para encender el Calefactor presione el boton de

encendido en la posicion de encendido (i). La luz roja se

mantendra prendida mientras el Calefactor este encendido.

(Figura 1)

6. Para apagar el Calefactor presione el boton de encendido

en la posicion de apagada (O). La luz roja se apagara y

desconecte el Calefactor del enchufe.

(Figura 1)

FUNCIÓN DE SEGURIDAD

1. Se incorpora un protector para sobrecargas térmicas a fin

de impedir el sobrecalentamiento.

2.

Si se alcanza una temperatura de sobrecalentamiento,

el

Calefactor se apaga automáticamente. Sólo podrá reanudar

su funcionamiento una vez que se reinicie la unidad.

Para Reiniciar el Calefactor:

1. desenchufe el Calefactor y espere 10 minutos para que

la unidad se enfríe.

2. después de 10 minutos, enchufe el Calefactor nuevamente

y siga la iNSTRUCCiÓN dE FUNCiONAMiENTO que se

describe en este manual de instrucciones.

Figura 1

1.

ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT

PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE

OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZ-

ARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.

WARNING:

FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG

FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVER-

HEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET.

2. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical

shock, or injury to persons.

3. Make certain that the room is equipped with a working smoke detector.

4. Make certain that the power source conforms to the electrical requirements of the Heater.

5. E x t r e m e c a u t i o n i s n e c e s s a r y w h e n a n y H e a t e r i s u s e d b y o r n e a r c h i l d r e n o r i n v a l i d s a n d w h e n e v e r t h e H e a t e r i s l e f t

o p e r ating unattended.

6. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to

fit in a polarized outlet only one way. if the plug does not fit fully in the outlet, reverse the plug. if it still does not fit, contact a

qualified electrician. do not attempt to defeat this safety feature.

7. do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any man-

ner. There are no user serviceable parts. Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to

5pm EST for assistance.

8. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.

9. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.

10. do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire,

or damage the Heater. do not block or tamper with the Heater in any manner while it is in operation.

11. To prevent a possible fire, do not block air intakes or exhaust in any manner. do not place on soft surfaces, like a bed, where open-

ings may become blocked.

12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the

Power Cord so the Heater or other objects are not resting on it. dO NOT run Power Cord under carpeting. dO NOT cover Power

Cord with throw rugs, runners, or similar coverings. Arrange Power Cord away from room traffic and where it will not be tripped over.

13. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater.

Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front

of the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.

14. A Heater has hot and arcing or sparking parts inside. dO NOT use the Heater in areas where gasoline, paint, or flammable liquids

are used or stored. dO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This

Heater is intended for general use ONLy.

15. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and

similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.

16. dO NOT use Heater outdoors.

17. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please

refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical

requirements for Agricultural Buildings.

THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).

18. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state

or local codes or standards relating to electrical requirements for Hazardous locations.

THIS HEATER DOES NOT MEET

THE REQUIREMENTS OF NEC ARTICLE 500 (2008).

WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED

CONTROL DEVICES.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk

of fire, electrical shock and injury to persons, including the following:

Read all instructions before using this Heater.

DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN

SERVICING OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND

UNPLUG HEATER BEFORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE

HEATER IS ON OR PLUGGED IN.

SAVE THESE INSTRUCTIONS

En la posicion de

encendido

En la posicion de

apagado

El boton de
Encendido