QUICKMOUNT; GENERAL SAFETY INFORMATION; SAVE THESE INSTRUCTIONS; Read all instructions before using this Fan. - Lasko 2265QM - Manual de uso - Página 2

Rev. B 10/12

2

2265QMES

Rev. B 10/12

7

2265QMES

MODELO 2265QM

ENSAMBLAJE DE LA BASE DE SOPORTE Y LA

CAJA DE CONTROL

(Figuras 1 y 2)

L A C A J A D E L C O N T R O L D E L V E N T I L A D O R D E B E S E R
MONTADA AL SOPORTE ANTES DE UTILIZAR EL VENT I L A D O R .

1. Cuidadosamente retire el Ventilador de la bolsa plástica y la caja.

2. Alinee los dos lados del ventilador con el soporte (Figura 1). Al

presionar los botones del soporte, empújelos hasta que queden

fijos en su lugar.

ADVERTENCIA:

Los tacos de plástico o hule, tales como

las patas de esta unidad, pueden pegarse a la superficie de los

muebles. La unidad podría dejar un residuo capaz de oscurecer,

manchar o dejar marcas permanentes en el acabado de ciertas

superficies de muebles, incluyendo superficies y pisos de madera.

3. Remover el tornillo de sujeción de la parte trasera de la caja

de control del ventilador.

4.

Asegurarse de que el alambre de la caja de control del

ventilador al motor está entre la parta del pedestal y la

rejilla tal como se muestra.

5. Insertar el tornillo de sujeción de la parte trasera del ventilador

a travez del orificio en la pata del pedestal tal como se muestra.

(Figura 2)

6. Alinear la caja de control del ventilador con el

tornillo de sujeción.

7. Apretar el tornillo de sujeción con la mano. No lo

aprete demasiado.

8. Conecte el cable eléctrico a un tomacorriente de 120 V.

Asegúrese que el enchufe encaje firmemente en el

tomacorriente.

C u a n d o l o s e n c h u f e s q u e d a n f l o j o s e n l o s

t o m a c o r r i e n t e s , p u e d e n d e s l i z a r s e p a r c i a l o

completamente fuera del tomacorriente con un leve

movimiento del cable adosado. Los tomacorrientes

en este estado podrían sobrecalentarse y representar

un grave peligro de incendio; si está cubierto por una

cortina o tela, el riesgo de incendio es aún mayor.

9. Encienda el Ventilador seleccionando la velocidad deseada

con la

Perilla de Encendido

situada al costado del Ventilador.

0 – Apagado

3 – Alta

2 – Media

1 – Baja

10. Para ajustar el ángulo vertical, mueva el cuerpo del Ventilador

hacia delante o hacia atrás hasta la posición deseada.

QUICKMOUNT ®DEL SOPORTE PARA LA PARED

1. Escoja una ubicación que monta que permitirá la instalación de

hardware (no suministró) directamente en sementales de pared

ni apoyo estructural adecuado.

2. Utilizar el paréntesis de pared como una plantilla, marca las ubi-

caciones de hoyo en la pared después de nivelar el paréntesis.

3. Abroche paréntesis de pared a montar superficie que utiliza 2

cierres calibrados apropiados. Taladre hoyos pilotos como sea

necesario.

(Vea la Figura 3).

El CUIDADO:

Verifique para eléctrico y/o las líneas de gas antes

de instalar el paréntesis de pared.

COLGANDO EL VENTILADOR EN EL SOPORTE

PARA LA PARED

1. Sostenga el ventilador en una posición vertical, como si estuviera

sobre en el suelo.

Su ventilador puede ser armado en la pared usando el nuevo

soporte para la paed de montaje rápido suministrados con

su ventilador. (Figuras 3 y 4)

QUICKMOUNT

®

SYSTEM

Figura 3

Figura 2

Figura 4

5/16" (7,94 mm) Tornillo X de la Demora 2" (50.8 mm)
Largo (el mínimo)

2. Coloque el borde trasero del pedestal en los ganchos del soporte

para la pared.

3. Permita que el pedestal gire hacia abajo de modo que los pies

de goma delanteros se apoyen en la pared debajo del soporte

de montaje.

4. Incline la cabeza del ventilador a la posición deseada.

Figura 1

Botón del

soporte

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electrical shock and injury to persons, including the following:

SAVE THESE INSTRUCTIONS

Read all instructions before using this Fan.

1. Make certain the power source conforms to the electrical requirements of the Fan.

2. Make certain that the room is equipped with a working smoke detector.

3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,

or injury to persons.

4. To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.

5. Unplug power cord before installing, servicing, or moving the Fan.

DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING

OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE

LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.

6. This Fan must

NOT

be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres

where gasoline, paint or flammable liquids are used or stored.

7.

DO NOT

use Fan in or near a window. Rain may create an electrical hazard.

8. Completely assemble Fan, according to instructions, before connecting to power supply.

REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN

WITH ANY SOLID STATE SPEED CONTROL DEVICES.

9. Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an exten-

sion cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed.

NEVER

use a single

extension cord to operate more than one Fan. Do not plug Fan into any other cord connected device, such as a power strip, cord

reel, surge protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.

10.

NEVER

operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in

any manner.

11.

NEVER

insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire,

or damage the Fan. To reduce the risk of fire,

DO NOT

block or tamper with the Fan in any manner while it is in operation.

12. Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power

Cord so the Fan or other objects are not resting on it.Do not run cord under carpeting. Do not cover cord with throw rugs, runners,

or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be

tripped over.

13. This Fan is not intended for use in wet or damp locations.

NEVER

locate a Fan where it may fall into a bathtub or other water con-

tainer.

NEVER

use Fan where flammable liquids are used or stored.

14.

NEVER

use Fan outdoors.

15. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please

refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical require-

ments for Agricultural Buildings.

THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).

16. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or

local codes or standards relating to electrical requirements for Hazardous locations.

THIS FAN DOES NOT MEET THE REQUIRE-

MENTS OF NEC ARTICLE 500 (2008).

The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle.

Under no circumstances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is

encountered, it must be replaced with a properly grounded three-prong receptacle installed in accordance with the

National Electrical Code (NEC) and all applicable local codes and ordinances. This work must be done only by a
qualified electrician, using copper wire only.

This plug is a safety feature. It contains a safety device (fuse) that should not be removed. Discard product if the attach-

ment plug is damaged. To reduce the risk of fire, electric shock and personal injury, DO NOT remove, replace, repair

or tamper with the originally supplied plug. If the Fan does not function properly, it may be due to the safety device

incorporated in this plug.

Botón del

soporte

VISTA DELANTERA

VISTA TRASERA