Lasko 754200 - Manual de uso - Página 2

Rev. A 3/09

2

754200ES

Rev. A 3/09

7

754200ES

MODELO 754200

FUNCIONAMIENTO

(Figura 1)

1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.

ADVERTENCIA:

Los tacos de plástico o hule, tales como

las patas de esta unidad, pueden pegarse a la superficie de los

muebles y/o a los pisos de madera. La unidad podría dejar un

residuo capaz de oscurecer, manchar o dejar marcas permanentes

en el acabado de ciertas superficies de muebles, incluyendo

superficies de madera y/o pisos de madera.
3. Asegúrese que la unidad esté en la posición

APAGADO

(0) antes

de conectar el Calefactor al tomacorriente.

4. Conecte el cable a un tomacorriente de 120 voltios.

A s e g ú r e s e q u e e l e n c h u f e e n c a j e fi r m e m e n t e e n e l

t o m a c o r r i e n t e .

Cuando los enchufes quedan flojos dentro de

los tomacorrientes, podrían deslizarse parcial o

completamente fuera del tomacorriente con el menor

movimiento del cable adosado. Los tomacorrientes

en este estado podrían sobrecalentarse y representar

un peligro de incendio grave; si queda cubierto por

una cortina o tela, el peligro de incendio es todavía

mayor.

5. Cuando el Calefactor se conecte por primera vez, se oirá un

“bip” y la

Luz de Encendido

se encenderá indicando que hay

electricidad en la unidad. La

Luz de Encendido

permanecerá

encendida hasta que el Calefactor sea desconectado del

tomacorriente eléctrico.

6. Gire la

Perilla de Encendido

hasta la posición deseada

( ) para

Sólo Ventilador

(SIN CALOR)

(1) para

Calor Bajo

(2) para

Calor Alto

(1500 Watts)

7. Para el funcionamiento del Calefactor, gire la

Perilla del

Termostato

a la posición más alta ( ).

8. Para APAGAR el Calefactor, gire la

Perilla de Encendido

a (0)

y desconecte el Calefactor del tomacorriente eléctrico.

ELEMENTOS DE SEGURIDAD

1. Hay un protector de sobrecarga térmica incorporado para evitar

el sobrecalentamiento.

2. Si se alcanza una temperatura de sobrecalentamiento, el

Calefactor se apagará automáticamente. Sólo podrá retomar

el funcionamiento cuando el usuario reinicie la unidad.

Para Reiniciar el Calefactor:

1. Desconecte el Calefactor y espere 10 minutos hasta que la

Unidad se enfríe.

2. Después que el Calefactor se haya enfriado, conecte la unidad

a un tomacorriente eléctrico de 120V~ y siga las instrucciones

de funcionamiento descriptas en este manual.

CONSEJOS DE SOLUCIÓN DE PROBLEMAS

Si su calefactor se apaga inesperadamente o no funciona, el

elemento de seguridad arriba mencionado podría haber sido

activado para evitar el sobrecalentamiento.

1. Asegúrese que el cable eléctrico esté conectado a un

tomacorriente eléctrico en funcionamiento.

2. Verifique la posición de su Termostato. El Calefactor puede

haberse apagado por haber alcanzado la posición de temperatura

deseada.

Si usted tiene un problema que no pueda ser resuelto siguiendo los

pasos enumerados arriba, comuníquese con Asistencia Técnica

al 800-233-0268, de lunes a viernes, entre las 8 a.m. y las 5 p.m.

EST.

INSTRUCCIONES DEL TERMOSTATO

1. Permita que el Calefactor caliente la habitación antes de fijar

el termostato.

2. Para ajustar el termostato, gire la Perilla del Termostato hacia la ( )

para aumentar la temperatura deseada o hacia la ( ) para reducir

la temperatura deseada.

3. Cuando se alcance la temperatura deseada, baje el termostato

hasta que la Unidad se apague. Esto se hace girando la Perilla

del Termostato hacia la ( ).

4. El Calefactor ahora mantendrá automáticamente la temperatura

seleccionada alternando la unidad entre las posiciones de

encendido y apagado. Para evitar que el Calefactor alterne entre

estas posiciones, ajuste el termostato.

Figura 1

Perilla de

Encendido

Perilla de

Termostato

Luz de

Encendido

SAVE THESE INSTRUCTIONS

1.

ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO NOT

PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE

OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZ-

ARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.

WARNING:

FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG

FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT

OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET.

2. Use this Heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical

shock, or injury to persons.

3. Make certain that the room is equipped with a working smoke detector.

4. Make certain that the power source conforms to the electrical requirements of the Heater.

5. E x t r e m e c a u t i o n i s n e c e s s a r y w h e n a n y H e a t e r i s u s e d b y o r n e a r c h i l d r e n o r i n v a l i d s a n d w h e n e v e r t h e H e a t e r i s

l e f t o p e r a t i n g u n a t t e n d e d .

6. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended

to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician. Do not attempt to defeat this safety feature.

7. Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any man-

ner. There are no user serviceable parts. Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm

EST for assistance.

8. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.

9. Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.

10. Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire,

or damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.

11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where open-

ings may become blocked.

12. Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the

Power Cord so the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power

Cord with throw rugs, runners, or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.

13. This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater.

Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of

the Heater and keep them at least 1 foot (0.3 m) from the sides and rear.

14. A Heater has hot and arcing or sparking parts inside. DO NOT use the Heater in areas where gasoline, paint, or flammable liquids

are used or stored. DO NOT use Heater in locations where flammable or explosive chemicals are stored, or in wet atmospheres. This

Heater is intended for general use ONLY.

15. This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and

similar indoor locations. NEVER locate a Heater where it may fall into a bathtub or other water container.

16. DO NOT use Heater outdoors.

17. Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.

18. This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined.

Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical

requirements for Agricultural Buildings.

THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).

19. This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state

or local codes or standards relating to electrical requirements for Hazardous locations.

THIS HEATER DOES NOT MEET

THE REQUIREMENTS OF NEC ARTICLE 500 (2008).

WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK – DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED

CONTROL DEVICES.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce the risk

of fire, electrical shock and injury to persons, including the following:

Read all instructions before using this Heater.

DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING

OR MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG HEATER BE-

FORE LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE HEATER IS ON OR PLUGGED IN.