Orbit 57985 - Manual de uso

FUNCTION

Manual Watering -

WATER ALL ZONES

Hold until the display shows MANUAL and flashes

WATER ALL ZONES. To WATER ALL ZONES for a default of

10 min. each*, wait without pressing a button until WATER

ALL ZONES stops flashing and watering will begin.

Hold until the display shows MANUAL and flashes

WATER ALL ZONES. Quickly press again and WATER A

PROGRAM apears. Wait until WATER A PROGRAM stops

flashing and press to select the desired program to run.

Once the program letter stops flashing, watering will begin.

Manual Watering -

WATER A PROGRAM

BUTTON PRESS

Manual operation

All programming and full functionality of the timer are available in the B-hyve

app. If you have the need, there are some basic operations you can perform

directly at your timer.

Rated input:

Australia—240V AC 50/60Hz 0.15A
Europe—230VAC 50/60Hz 0.15A
USA—120V AC 60Hz 0.2A

Max load:

AUS & EU—24V AC 1 Amp 50/60 Cycle
USA—24VAC 1 Amp 60Hz

Temperature Operating Range:

Operating: 32–158° F (0–70° C)
Storage & transport:
-4–176° F (-20–80° C)

Humidity Operating Range:

Operating: 0–80% | Storage & transport: 0–90%

Altitude:

6,500' (2,000 meters)

IP65 Rating
Installation Class II
Over Voltage Category II

FCC & IC Statement

This device complies with Part 15 of the FCC Rules and Industry Canada license exempt RSS standards.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause

undesired operation. FCC Warning: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help This device meets the FCC and IC

requirements for RF exposure in public or controlled environments. The end user is advised to maintain

a distance of 20 cm from the controller and any personnel to ensure compliance with RF exposure

regulations.

This Class B digital apparatus complies with Canadian ICES-003

DÉCLARATION DE FCC ET L’IC

Cet appareil est conforme à la section 15 de la Règlementation de la FCC et la norme RSS d’Industry

Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer

d’interférences nuisibles, et (2) cet appareil doit tolérer toutes les interférences, dont les interférences

pouvant causer un fonctionnement non désiré. Cet appareil numérique de classe B est conforme à la

norme canadienne ICES-003.

Remarque: cet appareil été testé et déclaré conforme aux limites d’exposition pour les appareils

numériques de classe B, selon la section 15 de la Règlementation de la FCC. Ces limites sont conçus pour

fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle.

Cet appareil produit, utilise et peut émettre de l’énergie radio fréquence et, si elle n’est pas installée et

utilisée conformément aux instructions, peut causer des interférences nuisibles aux communications

radio. Cependant, il n’est pas garantie que des interférences ne se produisent pas dans une installation

particulière. Si cet appareil cause des interférences gênantes à la réception d’un signal radio ou de

télévision, ce qui peut être déterminé en allumant et en éteignant l’appareil, l’utilisateur peut corriger les

interférences en suivants une des mesures suivantes :

• Réorientez ou repositionnez l’antenne de réception.

• Augmentez la distance entre l’appareil et le récepteur.

• Branchez l’appareil dans une prise sur un circuit différent du circuit sur lequel le récepteur est branché.

• Consulter le revendeur ou un technicien radio/TV expérimenté pour obtenir de l’aide. Cet appareil est

conforme aux exigences de la FCC et de l’IC concernant

l’exposition aux ondes dans un environnement public ou contrôlé. Il

est conseillé à l’utilisateur final de maintenir une distance de 20 cm du

contrôleur pour assurer la conformité aux réglementations d’exposition

RF. Information de conformité pour le Canada

SPECIFICATIONS

THE B-HYVE APP

Install the B-hyve® app on your smart device

You will need a smart device to connect the timer to Wi-Fi.

Note:

The app will guide you through initial set up of your sprinkler timer. In

addition, there are help icons throughout the app with more information and

useful tips.

timer connected

symbol

running status/

messaging

rain delay

calendar

program list

weather

& temp.

stop watering

next zone

settings

zone list

remote control or

home button

Need Help?

If the app and the website don’t have what you’re looking for,

please go to our website before returning this sprinkler timer to

the store.

call us

1-801-299-5555

text us

801-905-8260

email us

[email protected]

or visit us at:

mybhyve.com

Manual Watering -

WATER A ZONE

Skip Zone

Cancel All

Watering

Rain Delay

Digital Lock-Out

Lights Off Mode

On/Off

Hard Reset

Hold until the display shows MANUAL and flashes

WATER ALL ZONES. Quickly press two more times and

WATER A ZONE appears. Wait until WATER A ZONE stops

flashing and quickly press to select the desired zone to

run. When the zone stops flashing the run time will begin

to flash. Quickly press to set the desired run time. Once

RUN TIME stops flashing, watering will begin.

Quickly press to skip currently running zone.

Hold between 2-5 sec.

Set in app; blinks yellow and display shows DELAY.

Enable/disable in app.

Enable/disable in app.

Hold for 10 seconds.

Quickly press 5 times.

*Default watering time for “WATER ALL ZONES” can be customized in the B-hyve App settings.

Battery Specifications:

Timer includes a non-replaceable CR2032 Lithium
battery.

This timer works with any standard 24V irrigation
solenoid.
The internal fuse is non-replaceable.