SAVE THESE INSTRUCTIONS; IMPORTANT SAFETY INFORMATION; Read all instructions before using this Fan.; CAUTION; INSTALACIÓN; FUNCIONAMIENTO - Air King 9018 - Manual de uso - Página 2

Rev. W 10/17

2

2084046

Rev. W 10/17

7

2084046

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electrical shock and injury to persons, including the following:

Read all instructions before using this Fan.

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:

DO NOT

use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,

gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the con-
tainers for these products!

ALWAYS

be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet

and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition
should be replaced by a qualified electrician.

ALWAYS

unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means

of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan
when not in use.

BE CERTAIN

that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.

The

Blue Plug™

on your AirKing fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed

or tampered with. To reduce the risk of fire, electric shock and personal injury,

DO NOT

attempt to remove, replace, repair or tamper

with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no
circumstances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be
replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and
all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.
DO NOT USE A THREE-PRONG TO TWO-PRONG ADAPTER. IMPROPER CONNECTION MAY CREATE THE RISK OF ELEC-
TRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.

•

AVOID

the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these

devices may overheat and cause a fire hazard.

•

DO NOT

route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire hazard.

•

ALWAYS

place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.

•

NEVER

insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.

•

DO NOT

block, cover or obstruct air flow to or from the fan while in operation.

•

DO NOT

use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location

may create a shock hazard.

•

DO NOT

run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture

or appliances. Arrange cord away from traffic area and where it will not be tripped over.

•

NEVER

use a single extension cord to operate more than one Fan or other electrical device.

•

DO NOT

use this Fan if it has been damaged or is not functioning properly.

•

THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008)

.This Fan is not suitable for use in agricultural

facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article

547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.

•

THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008)

.This Fan is not suitable for use in hazardous

locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical

requirements for hazardous locations.

CAUTION

Parrilla

Posterior

Tuerca

Plástica

Aspa

Rotador

Parrilla

Anterior

Ornamento

Detalle 1

INSTALACIÓN

1. Coloque un perno prisionero detrás de la pared. Si no puede encontrar un perno prisionero, usted podrá encontrar tipos especiales

de pernos de anclaje en su ferretería local.

2. Fije la Placa de Montaje a la pared con los Tornillos que vienen incluidos (Tornillos para Madera #8 X 1 1/4"). Procure que la brida

apunte hacia arriba, como se muestra en la ampliación que se encuentra más arriba (vea la ampliación #1)

3. El Ventilador ahora está listo para ser colgado en la Placa de Montaje.

ARMADO

(Figura 1)

1. Coloque la

Parrilla Posterior

en el

Motor

, alineando la lengüeta de la

Parrilla Posterior

con la ranura que se encuentra en el

Motor

.

(Detalle 1)

2. Asiente totalmente la

Parrilla Posterior

en el

Motor

y fíjela con la

Tuerca Plástica

, haciéndola girar en el Sentido de las Manecillas

del Reloj.

3. Deslice el

Aspa

hasta montarla en el Eje del Motor. (Alinee la ranura que se encuentra en el cubo del aspa con la clavija del eje del

motor.)

(Detalle 2)

4. Para fijar el Aspa, atornille el

Rotador

en el Eje en el sentido

Contrario de las Manecillas del Reloj

hasta que se encuentre fijo en el

cubo del

Aspa

.

5. Encaje la

Parrilla Anterior

en su lugar.

FUNCIONAMIENTO

OSCILACIÓN VARIABLE:

Jale la perilla de oscilación ubicada en la parte posterior del motor hacia arriba. Empuje la perilla de oscilación

hacia abajo y el ventilador oscilará describiendo el ángulo fijado.

ÁNGULO VERTICAL:

Para ajustar el ángulo vertical, incline el cabezal del ventilador hacia arriba o abajo, según prefiera.

VELOCIDAD:

La velocidad se controla mediante un interruptor activado con una cadenilla de tiro. La velocidad fijada se indica mediante

la perilla del interruptor ubicada en la cubierta anterior (Apagado – Alta – Mediana–– Baja – Apagado).

CABLE DE ALIMENTACIÓN ELÉCTRICA:

Enchufe el cable eléctrico en un tomacorriente de pared (120 Voltios CA, 60 Hz).

MODELO 4CH64G/9018G

DESCRIPCIÓN

El ventilador oscilante Air King® de 18” (45,7 cm), montado a la pared, le ofrece control de velocidad mediante una cadenilla de tiro, oscilación variable,

un motor de capacitador con partición permanente y parrillas que cumplen con las regulaciones de OSHA.

ESPECIFICACIONES

Motor ............................................ 120V, 60Hz

Tamaño de paletas ...................... 18" (45,7 cm)

Velocidades ................................. 3
Control .........................................

Rotario/

Cordón

Distribución del flujo de aire ....... 90°

Aprobaciones ............. .................Catalogación ETL. El protector de malla cerrada del ventilador satisface las normas OSHA.

MODELO 4CH64G/9018G

VELOC. ALTA MEDIA BAJA

CFM

1955

1700

1380

M

3

/s

0.92 0.80 0.65

RPM

1100

950

750

Amps

0.75 0.60 0.50

Watts

85 75 65

dB

A 51 48 43

Motor

Clavija

Ranura

Detalle 2