OPERATION - Lasko 2 x LKO-5160 - Manual de uso - Página 3

Lasko 2 x LKO-5160

Calentador Lasko 2 x LKO-5160 - Manual de uso, léela gratuitamente en línea en formato PDF. Esperamos que esto te ayude a resolver cualquier duda que puedas tener. Si tienes más preguntas, contáctanos a través del formulario de contacto.

1 Page 1 2 Page 2 3 Page 3 4 Page 4 5 Page 5
Página: / 5
Página anteriorPágina siguiente

Índice:

Cargando la instrucción

Rev. E 4/17

10

5160ES

Rev. E 4/17

3

5160ES

MODEL 5160

Figure 2

Timer Function in

Low Heat

Timer Function in

High Heat and Automatic

Temperature Control

OPERATION

1. Carefully remove the Heater from the bag and the carton.
2. Place the Heater on a firm, level surface. Plastic or rubber tabs,

like the feet on this unit, may stick to furniture surfaces and/
or hardwood floors. The unit may leave a residue that could
darken, stain or leave permanent blemishes on the finish of
certain furniture surfaces, including wood surfaces, and/or
hardwood floors.

3. Plug the cord set into a 120 volt outlet.

Be sure that the plug fits tightly into outlet.

When plugs fit loosely into receptacles, they may

slip partially or completely out of the receptacle

with only the slight movement of the attached cord.

Receptacles in this condition may overheat and pose

a serious fire hazard; if covered by a curtain or drape,

the fire hazard is even greater.

4. When the Heater is initially plugged in, there will be a “beep”

and the

Power Light

will come on indicating that there is power

to the unit. The

Power Light

will remain lit until the Heater is

unplugged from the electrical outlet.

5. Turn the Heater ON by pressing the

Power Button

( ).

6. When initially turned on, the Heater will display the current

room temperature in ° Fahrenheit. Press the ( ) and ( ) but-
tons at the same time to change the display to ° Celsius. Press
the same two buttons together again to change the display back
to ° Fahrenheit.

7. Upon turning the Heater on, the unit will be in HIGH heat ( ) (1500

Watts) and will display the current room temperature

(Figure 1)

8. Press the ( ) button for LOW heat ( ).
9. To turn the Heater OFF, press the

Power Button

( ) and unplug

the Heater from the electrical outlet.

Figure 3

Display reflects High Heat and

Automatic Temperature Control Function

AUTOMATIC TEMPERATURE CONTROL

(Figure 3)

The automatic temperature function will only operate on "High"

heat ( ). You cannot set the temperature automatically when

the unit is in the low heat mode.
1. To set the room at a specific temperature press the ( ) or ( )

buttons to the desired temperature. The display will now reflect

the ( ) and the temperature will be flashing. The Heater is now

in Auto Temperature Mode.

2. When you reach the temperature at which you want to set the

unit, the set temperature will flash several times and then the

display will return to indicate the current room temperature and

will gradually change as the room temperature changes. NOTE:

the temperature display does not indicate the temperature of

the heated air being emitted by the heater.

3. Once the room temperature reaches 2 degrees above the set

temperature, the Heater will shut off. Once the room tempera-

ture reaches 1 degree below the set temperature, the Heater

will turn back on and continue to cycle off and on to maintain

the set temperature.

4. This function will cancel if the ( ) button is pressed. The Heater

will now be in High heat ( ) and run continuously.

NOTE:

It is normal for the Heater “fan” to run for approximately 15

seconds when the Heater shuts off after reaching the set
temperature.

OSCILLATION:

Pressing the

Oscillation Button

( ) will allow the Heater to oscil-

late back and forth. To stop the oscillation, press the

Oscillation

Button

( ) again. When the Heater is in Automatic Temperature

Control, the oscillation function will stop when the set temperature
is reached and resume when the Heater turns back on.

Figure 1

Display when initially turned on

TIMER FUNCTION:

The timer function may be activated when the Heater display is in
any function or speed.

(Figure 2)

This function allows you to set

the length of time the Heater will run before turning itself off, from
1 hour to 8 hours. Pressing the

Timer Button

( ) will increase the

length of time by 1 hour each time this button is pressed. After the
display reflects 8 hours, pressing the

Timer Button

( ) once more

will reset the Heater to run continuously. The Heater will turn off
when the set time has elapsed. The unit can be turned back on by
pressing the

Power Button

( ).

MODELO 5160

Si usted pierde su mando a distancia, por favor Cliente de llamada Serive para ordenar un reaplacement en 1-800 -233-0268,

de lunes a viernes, entre las 8 a.m. y las 5 p.m. (Horario Estándar del Este de los Estados Unidos)

.

Vista de frente del

Control Remoto

Vista posterior del

Control Remoto

Figura 4

CONTROL REMOTO:

Todas las funciones ejecutadas con el Control Remoto funcionan idénticamente a los controles manuales.

(Figura 4)

1. Retire el tornillo de tapa de la batería antes de instalar dos baterías "AAA" (no incluidas).
2.

No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-cinc), recargables (níquel-cadmio) o
de iones de litio.

3. NO SE DESHÁGA DE BATERÍAS EN EL FUEGO. BATERÍAS PUEDEN ESTALLAR O PUEDEN SALIRSE.

Retire el tornillo

antes de la

instalación de las

baterías

Página anteriorPágina siguiente

"Cargando la instrucción" significa que debes esperar hasta que el archivo se cargue y puedas leerlo en línea. Algunas instrucciones son muy grandes y el tiempo de carga depende de la velocidad de tu conexión a Internet.

Resumen

Página 2 - CONSEJOS DE SOLUCIÓN DE PROBLEMAS; SAVE THESE INSTRUCTIONS; Read all instructions before using this Heater.; IMPORTANT SAFETY INSTRUCTIONS; CAUTION; WARNING

Rev. E 4/17 2 5160ES 11 5160ES Rev. E 4/17 CONSEJOS DE SOLUCIÓN DE PROBLEMAS Si su calefactor se apaga inesperadamente o no funciona, el elemento de seguridad arriba mencionado podría haber sido activado para evitar el sobrecalentamiento.1. Asegúrese que el cable eléctrico esté conectado a un tomaco...

Página 3 - OPERATION

Rev. E 4/17 10 5160ES Rev. E 4/17 3 5160ES MODEL 5160 Figure 2 Timer Function in Low Heat Timer Function in High Heat and Automatic Temperature Control OPERATION 1. Carefully remove the Heater from the bag and the carton.2. Place the Heater on a firm, level surface. Plastic or rubber tabs, like the ...

Página 4 - FUNCIONAMIENTO

Rev. E 4/17 4 5160ES Rev. E 4/17 9 5160ES If you lose your remote control, please call Customer Service to order a replacement at 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m. and 5:00 p.m. EST. MODEL 5160 CONTROL AUTOMÁTICO DE LA TEMPERATURA (Figura 3) La función de temperat...

Otros modelos de calentadores Lasko

Todos los calentadores Lasko