SAVE THESE INSTRUCTIONS; Read all instructions before using this Heater.; IMPORTANT SAFETY INSTRUCTIONS; CAUTION; WARNING; Partes Incluidas; CONTROL AUTOMÁTICO DE LA TEMPERATURA; Cuerpo; Controles - Lasko CT22415 - Manual de uso - Página 2

Rev. A 5/22

2

CT22415BBBES

SAVE THESE INSTRUCTIONS

Read all instructions before using this Heater.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, these instructions and warnings should always be

followed to reduce the risk of fire, electrical shock and injury to persons:

CAUTION

• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so the

Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or similar
coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.

• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep combustible

materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep them at least 1
foot (0.3 m) from the sides and rear.

• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor locations.

NEVER locate a Heater where it may fall into a bathtub or other water container.

• DO NOT use Heater outdoors.
• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National

Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings.

THIS Heater DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).

• This Heater is not suitable for use in ha zardous locations. Please refer to National Electric Code (NEC) Ar ticle 500 or applicable state or local

codes or standards relating to electrical requirements for Ha zardous locations.

THIS Heater DOES NOT MEET THE REQUIREMENTS OF NEC

ARTICLE 5 0 0 (2 0 0 8).

• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Heater. If this occurs, move the

Heater to another location.

• Keep Heater remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Heater.

WARNING

WARNING

• PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT

PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET
ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT
PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON SAME CIRCUIT AS HEATER.

• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS TIGHTLY

INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING. IF NECES-
SARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER WITH ANY SOLID
STATE SPEED CONTROL DEVICES.

• Make certain that the power source conforms to the electrical requirements of the Heater.
• Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended.

Never leave children unattended when the Heater is on or plugged in.

• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a

polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Do not attempt to defeat this safety feature.

• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where

flammable or explosive chemicals are stored, or in wet atmospheres.

• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.

To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.

• Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
• Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or damage

the Heater. Do not block or tamper with the Heater in any manner while it is in operation.

• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked. Do not

depend on the on/off switch as the sole means of disconnecting power when servicing or moving the Heater. Always unplug the power cord.

Rev. A 5/22

7

CT22415BBBES

Partes Incluidas

FUNCIÓN SAVE-SMART

®

Prensa (

) para activar la función Save-Smar t

®

.

1. Para fijar una temperatura especifica en la habitación, presione los botones de ( ) y ( ) hasta la temperatura deseada. (Nota: La temperatura

predefinida es 72º F).

2. Cuando alcanzar la temperatura en la cual desea establecer la unidad, la temperatura fijada titilará varias veces y luego la pantalla volverà a indicar

la temperatura actual y cambiará gradualmente a medida que cambia la temperatura de la habitación.

3. Cuando la temperatura ambiente es menos que la temperatura fijada, el Calefactor funcionará el modo ALTO.
4. Una vez que el termostato alcance la temperatura fijada, el Calefactor cambiará automáticamente al modo BAJO para conser var energía.
5. Una vez que la temperatura ambiente de la habitación alcance los 4 grados por encima de la temperatura fijada, el Calefactor se apagará. El

Calefactor se encenderá de nuevo y continuará con el ciclo de apagado y encendido en el modo bajo para mantener la temperatura fijada. Todo
esto sucede automáticamente con la Tecnología de Save-Smar t

®

del producto Lasko. Para desactivar la función de Save-Smar t

®

, apriete el botón

de Save-Smar t

®

otra vez o el botón de (

) para calor alto/bajo continuo.

CONTROL AUTOMÁTICO DE LA TEMPERATURA

La función de temperatura automática sólo operará en calefacción Alta. No puede fijar la temperatura automáticamente cuando la unidad se encuen-
tre en la modalidad de calefacción Baja.
1. Para fijar una temperatura específica en la habitación, presione los botones de ( ) o ( ) hasta la temperatura deseada. La pantalla mostrará au-

tomática y la temperatura estará iluminada. El Calefactor ahora se encuentra en la modalidad de temperatura automática.

2. Cuando alcance la temperatura en la cual desea establecer la unidad, la temperatura fijada titilará varias veces y luego la pantalla volverá a indicar

la temperatura actual y cambiará gradualmente a medida que cambia la temperatura de la habitación.

NOTA:

la pantalla de la temperatura no indica la temperatura del aire caliente emitido por el Calefactor .

3. Una vez que la temperatura de la habitación alcanza los 2 grados por encima de la temperatura fijada, el Calefactor se apagará. Una vez que la

temperatura de la habitación alcanza 1 grado por debajo de la temperatura fijada, el Calefactor se encenderá de nuevo y continuará con el ciclo
de apagado y encendido para mantener la temperatura fijada.

4. Esta función se cancelará si el botón ( ) está presionado. Ahora el Calefactor estará en calefacción Alta y operará continuamente.

NOTA:

Es normal que el “ventilador” del Calefactor funcione durante aproximadamente 15 segundos después que el Calefactor se haya apagado tras

alcanzar la temperatura fijada.

1 Cuerpo

2 Control

Remoto

1

2

Controles

Control Automático de la Temperatura

Presione para Disminuir la temperatura ambiente deseada.

Control Automático de la Temperatura

Presione para Aumentar la temperatura ambiente deseada.

Botón de Modo de Calor

Presione para alternar entre Calor Alto y Bajo

Botón Save-Smart

®

Presione para activar la función Save-Smart

®

Botón de Oscilación

Presione para Iniciar/Detener la función de oscilación.

Botón de Temporizador

El temporizador se puede configurar para 8 horas. Continúe pul-
sando el Botón del Temporizador para llegar a la configuración
de tiempo deseada. La luz se vuelve verde cuando se activa.

Botón de Encendido

ENCENDIDO/APAGADO el Calefactor

presionando el Botón de Encendido