SAVE THESE INSTRUCTIONS; Read all instructions before using this Fan.; IMPORTANT SAFETY INSTRUCTIONS; CAUTION; WARNING; ENSAMBLAJE - Lasko T36211 - Manual de uso - Página 2

NEW 12/18

2

T36211ES

SAVE THESE INSTRUCTIONS

Read all instructions before using this Fan.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, these instructions and warnings should always be

followed to reduce the risk of fire, electrical shock and injury to persons:

CAUTION

•

AVOID

the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these de-

vices may overheat and cause a fire hazard.

•

DO NOT

route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a

fire hazard.

•

ALWAYS

place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.

•

NEVER

insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.

•

DO NOT

block, cover or obstruct air flow to or from the Fan while in operation.

•

DO NOT

use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may

create a shock hazard.

•

DO NOT

run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture

or appliances. Arrange cord away from traffic area and where it will not be tripped over.

•

NEVER

use a single extension cord to operate more than one Fan or other electrical device.

•

DO NOT

use this Fan if it has been damaged or is not functioning properly.

• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,

move the Fan to another location.

• Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
•

THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008)

. This Fan is not suitable for use in agricultural

facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.

•

THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008)

. This Fan is not suitable for use in hazardous lo-

cations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.

NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes
and modifications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.

WARNING

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:

DO NOT

use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,

gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!

ALWAYS

be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and

create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should
be replaced by a qualified electrician.

ALWAYS

unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means

of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the
Fan when not in use.

BE CERTAIN

that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.

The

Blue Plug

™

on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed

or tampered with. To reduce the risk of fire, electric shock and personal injury,

DO NOT

attempt to remove, replace, repair or tamper

with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.

THIS FAN HAS A POLARIZED PLUG

(one blade is wider than the other). This plug is designed to fit into the outlet only one way.

Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the
plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.

NEW 12/18

7

T36211ES

MODELO T36211

ENSAMBLAJE

1. Para fácil ensamblado, apoye el ventilador de modo tal que la parrilla

frontal y el panel de control apunten hacia arriba.

2. Arme las

Bases de Apoyo

interconectando las

Salientes

en la

Base

de Apoyo A

dentro de los

Orificios de Salientes

en la

Base de Apoyo

B

. Introduzca el

Cable Eléctrico

a través del orificio grande en el

centro de la

Montura de la Base de Apoyo

.

(Figura 1)

3. Alinee las

Lengüetas de Alineación de la Montura de la Base de

Apoyo

con las ranuras de alineación en la parte inferior del ventilador,

teniendo cuidado de que el canal del cable en la parte inferior de
la base de apoyo debe estar apuntando hacia la parte posterior del
ventilador.

(Figura 2)

4. Asegure la

Montura de la Base de Apoyo

a la parte inferior

del ventilador con

(4) Tornillos de Largo

. Suavemente elimine

cualquier sobrante del

Cable Eléctrico

y colóquelo en el

Orificio

de Colocación del Cable

.

(Figura 3)

Figura 4

Botón de

Oscilación

Botón de

Encendido

Botón

Temporizador

Botón

Velocidad

Si usted pierde su mando a distancia, por favor Cliente de llamada Serive
para ordenar un reaplacement en (800) 233-0268, de lunes a viernes, entre
las 8 a.m. y las 5 p.m. (Horario Estándar del Este de los Estados Unidos).

CONTROL REMOTO

1. Instale las dos baterías “A A A” (no incluídas), como se muestra en la

Figura 5

.

2. Todas las funciones realizadas con el Control Remoto pueden re-

alizarse de igual forma con los Controles Manuales.

3. No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas,

estándar (carbono-cinc) o recargables (níquel-cadmio).

4. NO ARROJE LAS BATERÍAS AL FUEGO, LAS BATERÍAS PUEDEN ES-

TALLAR O PUEDE DERRAMARSE EL LÍQUIDO CONTENIDO.

OPERACIÓN

Puede operar este ventilador con los controles manuales ubicados en la parte
superior de la unidad

(Figura 4)

o con el control remoto

(Figura 5)

.

1. Coloque el ventilador sobre una superficie firme y nivelada.

ADVERTENCIA:

Los tacos de plástico o hule, tales como las patas de esta

unidad, pueden pegarse a la superficie de los muebles. La unidad podría
dejar un residuo capaz de oscurecer, manchar o dejar marcas permanentes
en el acabado de ciertas superficies de muebles, incluyendo superficies
y pisos de madera.
2. Conecte el cable eléctrico a un tomacorriente de 120 volts.

Asegúrese que el enchufe encaje
firmemente en el tomacorriente.

De no encajar firmemente en el tomacorriente, podrían de-
slizarse parcial o completamente fuera del tomacorriente
apenas con un ligero movimiento del cable conectado. Los
receptáculos en esta condición pueden sobrecalentarse y
constituir un grave riesgo de incendio; si está cubierto por
una cortina, el peligro de incendio es aún mayor.

3. Suministre corriente eléctrica al ventilador al presionar el

Botón De

Encendido

( ). El ventilador operará inicialmente en velocidad alta,

velocidad 3.

4.

VELOCIDAD DEL VENTILADOR:

Ahora usted puede ajustar la veloci-

dad del ventilador al nivel deseado, 3, 2, o 1 oprimiendo el

Botón de

Velocidad

(

).

5.

OSCIL ACIÓN:

Presione el

Botón de Oscilación

(

) para iniciar y de-

tener la función de oscilación.

6.

FUNCIÓN DE TEMPORIZADOR:

Este ventilador está equipado con

un temporizador. El temporizador se puede configurar para 1-7 horas.
Continúe pulsando el

Botón del Temporizador

(

) para llegar a la con-

figuración de tiempo deseada. Para cancelar el temporizador, pulse el

Botón de Temporizador

(

) hasta que las luces se apaguen.

7. Después de apagar el ventilador, desconecte la unidad del tomacor-

riente eléctrico.

Figura 1

Base de

Apoyo B

Base de

Apoyo A

Salientes

Orificios

de Salientes

Montura de la Base de Apoyo

Tornillos

Montura de la

Base de Apoyo

Cable

Eléctrico

Orificio de

Colocación

del Cable

Figura 3

Montura de la Unidad de base a Parte Inferior

Ranura de
Alineación

Lengüeta de

Alineación de la

Montura de la

Base de Apoyo

Figura 2

Canal

del Cable

Mantenga las baterías fuera del alcance de los niños

Figura 5

TIMER

POWER

OSC

SPEED

LOUVERS

TIMER

POWER

OSC

SPEED

IONIZER

TIMER

POWER

OSC

SPEED

Botón de

Encendido

Botón

Velocidad

Botón

Temporizador

Baterías

AAA

Botón de

Oscilación