Installation Instructions - Stainless Door Panel; Door Trim Pinch; STEP 1 INSTALL STAINLESS PANEL; Risque de pincement - Monogram ZIR361NPRII - Manual de uso - Página 19
Frigorífico Monogram ZIR361NPRII - Manual de uso, léela gratuitamente en línea en formato PDF. Esperamos que esto te ayude a resolver cualquier duda que puedas tener. Si tienes más preguntas, contáctanos a través del formulario de contacto.
Índice:
- Página 2 – ANTES DE COMENZAR; IMPORTANTE; PRECAUCIÓN; ADVERTENCIA; FORMA ADECUADA DE DESCARTAR SU ELECTRODOMÉSTICO
- Página 4 – Installation Instructions - Reversing the Door Swing; WARNING; Risque de
- Página 5 – STEP 2 REMOVE DOOR; Door Hinge Pinch
- Página 8 – STEP 4 INSTALL ANTI-TIP BRACKET; Dual install
- Página 9 – Electrical Shock Hazard.; Trisque de
- Página 10 – ON; STEP 12 START ICEMAKER; OFF; CAUTION; ATTENTION
- Página 13 – STEP 7 INSERTING/SECURING INTO
- Página 17 – STEP 11 START ICEMAKER (freezer models)
- Página 19 – Installation Instructions - Stainless Door Panel; Door Trim Pinch; STEP 1 INSTALL STAINLESS PANEL; Risque de pincement
- Página 21 – /4” CUSTOM DECORATIVE PANEL DIMENSIONS; Design Guide - Custom Overlay Door Panel; CUSTOM HANDLE DESIGN GUIDE; Door Trim Pinch Point
59
31-1000600 Rev. 0
Installation Instructions - Stainless Door Panel
Stainless Steel Door Panel Kits are available with either
Euro handles or Pro handles.
Stainless steel panel is fully assembled with brackets
and handle already installed
as a LH or RH swing door.
LH door kits can be modified to fit RH swing units and
RH door kits can be modified to fit LH swing units.
Leave the protective film on the door until the
installation is complete.
WARNING
Door Trim Pinch
Point Hazard
Improper installation can lead to a finger pinch point
hazard between the side door trim and the cabinets
when operating the door, especially with children.
To minimize this risk you must follow the installation
instructions for cabinet dimensions, trim assembly, and
door stop angle.
STEP 1 INSTALL STAINLESS PANEL
Ŷ
Remove bottom hinge cover and retain the 4 T30
Torx screws for later installation.
Ŷ
Open door to 90°. Slide the
panel onto the door with the
panel brackets interlocking
on top and bottom with the
door brackets (make sure
not to slide the panel into
the cabinetry surround).
Center the panel on the
door, then slowly close
the door while watching to
make sure the panel does
not contact the surrounding
cabinetry.
Ŷ
With the door fully closed,
carefully slide the panel towards
the cabinetry with the goal gap
of 1/8”.
STEP 2 ADJUST STAINLESS PANEL
Ŷ
Door adjustments will be
made with 12 set screws
provided. Each corner
of the door will use 3
adjustment set screws.
Use a 1/8” allen wrench
to install the set screws in
the order as instructed.
Ŷ
The set screws behind
the top and bottom
support brackets are
partially hidden.
Bottom
hinge
cover
T30 Torx
screws
Door
Bracket
Panel
Bracket
Panel
1/8” gap
Cabintery
Surround
Overlay
Panel
Set
Screws
Hidden Set
Screw
Set
Screws
AVERTISSEMENT
d
Risque de pincement
de doigts.
IUne installation incorrecte peut poser un risque
de coincement de doigts entre la garniture de porte latérale
et les armoires en manipulant la porte, en particulier pour les
enfants. Pour réduire ce risque, vous devez suivre les ins-
tructions d’installation relatives aux dimensions d’armoire, au
montage des garnitures et à l’angle de l’arrêt de porte.
ADVERTENCIA
Riesgo de
Lastimadura con el Borde de la Puerta
Una instalación inadecuada puede conducir a riesgos de
pellizcos de dedos entre el borde lateral de la puerta y los ga-
binetes al utilizar la puerta, especialmente con los niños. A fin
de minimizar este riesgo, usted deberá seguir las instruccio-
nes de instalación para dimensiones de gabinetes, ensambles
de bordes y ángulos de detención de puertas.
ZK1SN189NLH
LH 18” Stainless Steel Door Panel
ZK1SN184NRH
RH 18” Stainless Steel Door Panel
ZK1SN249NLH
LH 24” Stainless Steel Door Panel
ZK1SN244NRH
RH 24” Stainless Steel Door Panel
ZK1SN309NLH
LH 30” Stainless Steel Door Panel
ZK1SN304NRH
RH 30” Stainless Steel Door Panel
ZK1SN369RLH
LH 36”Stainless Steel Door Panel
ZK1SN364RRH
RH 36”Stainless Steel Door Panel
ZKSP1H1CNSS
Minimalist Handle for Stainless
Steel Panels Only
ZKSP1H1PNSS
Statement Handle for Stainless
Steel Panels Only
"Cargando la instrucción" significa que debes esperar hasta que el archivo se cargue y puedas leerlo en línea. Algunas instrucciones son muy grandes y el tiempo de carga depende de la velocidad de tu conexión a Internet.
Resumen
4 31-1000600 Rev. 0 Safety Information ANTES DE COMENZAR Lea estas instrucciones en su totalidad y atentamente. • IMPORTANTE – Conserve estas instrucciones para uso del inspector local. Cumpla con todos los códigos y ordenanzas gubernamentales. • Nota para el Instalador – Asegúrese de que el Com...
9 31-1000600 Rev. 0 Installation Instructions - Reversing the Door Swing STEP 1 REMOVE UPPER ENCLOSURE Ŷ Open the front cover of the enclosure to 90°. Locate filter and filter removal tool. Filter should be as shown. Ŷ 5RWDWH¿OWHUóWXUQ counterclockwise (use ¿OWHUUHPRYDOWRROLI needed). Ŷ 3XOO¿OWHUWR...
10 31-1000600 Rev. 0 Installation Instructions - Reversing the Door Swing STEP 2 REMOVE DOOR Ŷ Open the door to the open position. Ŷ Have a second person support the open door. Ŷ Remove 2 T30 Torx screws securing the bottom hinge to the case. Ŷ Remove the 2 T30 Torx screws securing the top hinge...